- 积分
- 258
- 在线时间
- 335 小时
- 最后登录
- 2020-3-26
- 阅读权限
- 50
- 精华
- 0
- UID
- 469109
- 帖子
- 224
- 精华
- 0
- 经验
- 258 点
- 金钱
- 190 ¥
- 注册时间
- 2012-2-3
|
楼主 |
发表于 2018-11-20 14:09
来自手机端
|
显示全部楼层
Accuphase T-109 Accuphase T-109 came! On August 31, 2013, I borrowed Accuphase T-109 from Mr. T from Okinawa for research. It is a high-end machine with a list price of 150,000 yen . Because it is expensive as it is used, it is a machine that can not be obtained easily. It is an FM dedicated synthesizer tuner featuring Advanced DGL detection . As a successor to this T-109, there is T-109V witha fixed price of 170,000 yen, but probably nothing will change, T-109 is more affordable. I think that the image of the general public is "high-end machine = high sensitivity", but this is not true in the audio world. As emphasis is placed on "high-end machine = high sound quality", the sensitivity is rather moderate. Therefore, in order to use such a high-end machine, the strongest electric field and the best environment with multipass is the minimum are necessary. According to Mr. T, there are the following troubles. Audio sounds but always mixed with noise. (It does not depend on radio condition) Sensitivity is bad. Quickly, degree & operation check appearance Overall it is pretty beautiful. If you look closely well there are several shallow scratches, but not so noticeable. I turned on the power while checking it as it got it There is no lamp out, all displays are normal, and the brightness is the same as new. All operations are normal. As long as we receive in the state of 90 dB strong electric field near our home, multipass: zero, the S meter also swings to full and it becomes stereo properly. I feel a kind of clipping distortion called Jiggets in the vicinity of the peak of the sound. In order to verify this scientifically, I tried T-109 to receive a radio wave of 83 MHz / 90 dB from the FM standard signal generator. IF of T-109 is NORMAL (WIDE). Up to the modulation degree of 100%, the waveform of the normal 1 kHz sinusoidal wave is not a sinusoidal wave like the right at the modulation degree of 133%, it deteriorates to the distortion factor of 25%, and the S / N also deteriorates to 40 dB or less. It is a wonderful sound when the degree of modulation is low, but this phenomenon seems to come from around 100%. The feeling that "when the sound is peaked" when it is checked with only the ear applies is perfect. I found that it is necessary to recover this by adjustment or repair. Although there is a problem of sound as described above, I feel that it will become ultra-high sound quality by repair and readjustment with the way that the S / N is shaky and sounds lively and sounds quiet. I tried opening the cover Making the board is very good. You can display enlarged pictures by removing the front end cover by clicking on the picture. It is a clean substrate with a clean board. Based on the lot number of IC used, this T - 109 was found to be made in 1995. Since the bottom plate comes off, maintenance is good, such as parts replacement. There is a black large box on the left side of the board. Is there something wonderful substrate in it? I examined, it was just a normal power transformer included. This box is just a Mitekure is. We are streamlining using ICs. Accuphase 426-0020-00 MCU AKM AK93C45 ... 8 Kbit Serial CMOS EEPROM JRC NJM 79 M 12 A 3-Terminal 0.5 A Negative Voltage Regulator (-12 V) JRC NJM 360 D ... High speed comparator JRC NJM 2904 D · · · Single-Supply Dual Operational Amplifier SANYO LA 3401 · · · VCO Non-Adjusting PLL FM MPX NEC C 2531 CS · · · Dual FET NEC uPC24M05 ... 3-Terminal Low Dropout Voltage Regulator (+ 5V) NEC uPC 24 M 12 ... 3 - Terminal Low Dropout Voltage Regulator (+ 12 V) NEC uPC 4570 HA ... Dual Ultra Low-Noise, Wideband, Operational Amplifier Toshiba TA 7060AP ... FM IF Amplifier Toshiba TA 7302 P ... FM IF Amplifier Toshiba TA 7310 P ... OSC & Mixer Toshiba TA 8129 Z ... FM IF System (Differential Peak Detection) Toshiba TC 4053 BP ... Single 8-Channel Multiplexer / Demultiplexer Toshiba TC 4584 BP ... Hex Inverting Schmitt Trigger Toshiba TC 74 HC 04 AP · · · Hex Inverter Toshiba TC 74 HC 14 AP ··· Hex Inverting Schmitt Trigger Toshiba TC 74 HC 86 AP ··· Quad Exclusive OR Gate Toshiba TC 74 HC 4060 AP ··· 14-stage binary ripple counter with oscillator Toshiba TC 9172 AP · · · High Speed PLL with Built-In Prescaler FM front end It is configured not on an independent front end but on a tuner board. Placed a shield case, it exudes a sense of quality. In the shield case, there is one Uniphase CF (UCF) and a PLL comparator (TC 9172AP) built-in. It is the following 5-unit varicap configuration. The tuning section can adjust all 2 tracking. (Antenna) → Tuning → Tuning → FET → Tuning → Tuning → Balanced Mxer (Dual FET IC) → IFT → FET → CF → To the IF section ← [OSC Synchronization (TR)] FM IF section NORMAL (WIDE) has the following configuration. The NARROW IF section is inserted so that it interrupts the forefront of the NORMAL IF section. (FE) → [FET] → [UCF] → [TA 7060 AP] → [UCF] → [TA 7302 P] → [IFT] → [TA 7302 P] → [IFT] → [TA 7310 P] → [IFT] → Detection section NARROW has the following configuration. (FE) → [FET] → [CF] → [TA 7060AP] → [CF] → [TA 7060AP] → [UCF] → [TA 7060AP] → [UCF] → [TA 7302 P] → [IFT] → [TA 7302 P] → [IFT ] → [TA 7310 P] → [IFT] → Detection section There is a dedicated IF section for S meter & synchronization point detection. (FE) → [FET] → [CF] → [TA 8129 Z] [IFT] → [NJM 2904 D] → S Meter / Muting The TA 8129 Z has a quadrature detection section, and the T meter output is between 9 and 13 pins (both ends of R 42). Adjust with TD 1 of IFT. Tuning point detection output is 7 pin. Advanced DGL detector DGL stands for Differential Gain Linear. Downconvert 10.7 MHz IF frequency to 2.5 MHz with [TA7310P] before DGL detection. The circuit diagram on the right is the down converting part. It is 13.2 MHz - 10.7 MHz = 2.5 MHz with [TA7310P] and [13.2 MHz crystal oscillator]. Because it is 2.4 MHz in the product catalog, I think that the specification was changed to 2.5 MHz somewhere in the production lot. クリスタル発振子を使っているので(ほぼ)無調整回路となっています。 KENWOOD や Pioneer のチューナではダウンコンバート後に急峻な LPF を入れているのですが、T-109 ではそのような LPF がないのに、デジタル処理に適した綺麗な波形(方形波)が得られています。 DGL 検波は右のような回路です。 CMOS IC の遅延特性を利用し、位相角0度の信号と位相角114度の信号 (いずれも 2.5MHz) を EX-OR した結果を積分して AF 信号を再生します。 以上のため、全くの無調整回路となっています。 原理的にパルスカウント検波そのものです。 TRIO/KENWOOD, Pioneer のパルスカウント検波より一歩進んだ回路と言えます。 T-109 のカタログの写真では、ディレイラインに使われるのは [74HC04] だけですが、今回の T-109 では最初の部分が [74HC14] に変更されており、[74HC14]×9+[74HC04]×12+[74HC86]×3=全部で24段 となっていました。 生産ロットのどこかで仕様変更されたのだと思います。 右のタイムチャートは回路図の A, B, C 点の波形例を示します。 タイムチャートの左は無変調時の場合で、右は変調されている場合です。 TRIO/KENWOOD, Pioneer のパルスカウント検波ではワンショットマルチを使うので、ノイズが多い微弱電波では、このワンショットが誤動作を起こし、歪が大幅に増大しますが、DGL 検波では誤動作しません。 微弱電波もそれなりに検波します。 [Advaced DGL] と [DGL] の違い DGL 検波の前に高速コンパレータ (NJM360D) があるのが [Advanced DGL] で、無いのが従来の [DGL] です。 MPX 部 [LA3401] で構成します。 VCO は 456kHz のセラロック発振子を使った無調整回路になっています。 この部分の調整はセパレーション調整だけです。 メモリバックアップ [AK93C45] の 8Kbit Serial CMOS EEPROM で実現します。 EEPROM なので電源を切っても記憶は永久に保存されます。 修理 IF NORMAL 受信時に、音がピークになる辺りで、ジッジッというクリッピング歪のようなものを感じる。 FM 標準信号発生器より電波を絞って入れてみると、50dB 以下あたりから大幅に S/N が劣化するのが確認できました。 T さんが「感度が悪い」とレポートされているのと合います。 調査の結果、IF NORMAL 増幅部の1段目である IC17 TA7060AP の故障と判明しました。 右の写真が故障していた TA7060AP です。 通常の TA7060AP は 5pin ですが、これは 7pin パッケージに入っている特殊型です。 (最初と最後の pin が使われていない。) 4pin, 5pin 共に +12V になってしまい、IC17 に全く電流が流れないのと同じ状態となります。 IC17 の 3pin (GND) の配線が外れたのと同じ状態です。 ハンダクラックかとも思い調べましたが、IC17 の故障でした。 手持ちの TA7060AP と交換して直りました。 歪感は完全に消滅し、高音質が蘇りました。 上記修理後の動作チェックで [MUTE] [9] [11] [13] [15] ボタンが動作しない現象が出ました。 上記の修理前には確かに動作していたのに、なぜか5個のボタンが動作しません。 The contacts of the above five buttons are matrix wired, and one contact is common. This common contact is input to 62 pin of Accuphase 426-0020-00 chip. As a result of the investigation, Accuphase 426-0020-00 chip between 62 pin and GND was DC resistance of about 70 Ω, which was broken inside the IC. This is the only way to replace the IC. There is no choice but to give up. Even if you do not like it, you can not use [MUTE] OFF and preset with the buttons [9] [11] [13] [15], so you can use it without any problem. Although five button operations can not be performed from the front panel, I think that it probably works with remote control operation. The faulty part is different from TA7060AP, it does not touch at all, and it is unknown why the breakdown has been reached. It may have broken down since this repair. Adjust by using FM / AM standard signal generator Panasonic VP-8175A (SSG), FM Stereo signal generator MEGURO MSG-2170 , frequency counter ADVANTEST TR 5822 as adjusted photo . After ten years the coils and trimmers are shifted. Adjustment point The adjustment points other than the FM front end are below. T-109 uses many unadjusted circuits, so adjustment points are small. Type Adjustment point Remarks VR VR1 MUTING LEVEL VR VR 2 S-METER VR VR 3 SEPARATION IFT TD 1 T-METER NULL IFT TD 2 IF DISTORTION 1 IFT TD 3 IF DISTORTION 2 IFT TD 4 2nd IF (2.5 MHz) Voltage check 電圧の実測値は正常でした。 ポイント 標準値 実測値 備考 IC1 (24M12) OUT +12V +12.01V チューナ/オーディオ用 IC2 (79M12A) OUT -12V -11.83V オーディオ用 IC3 (24M05) OUT +5V +4.97V ロジック用 FM 受信部の調整 手順 SSG周波数 SSG出力 T-109 の設定 調整箇所 TP 及び調整値 備考 1 - - SELECTIVITY : NORMAL METER : SIGNAL FILTER: OFF MUTE : OFF MONO : OFF - - 2 - - 76MHz 受信 フロントエンド内 L4 TP1 CV~G 間電圧 = 1.15V (実測値) 3 - - 90MHz 受信 フロントエンド内 VC5 TP1 CV~G 間電圧 = 17.5V (実測値) 4 - - - - 手順2と3を数回繰り返す VT トラッキング調整 5 76MHz 30dB 変調 : OFF 76MHz 受信 フロントエンド内 L1 L2 T1 L3 TP2 S~G 間電圧 = 最大 6 90MHz 30dB 変調 : OFF 90MHz 受信 フロントエンド内 VC1 VC2 VC3 VC4 TP2 S~G 間電圧 = 最大 7 - - - - 手順5と6を数回繰り返す RF トラッキング調整 8 83MHz 30dB 変調 : OFF 83MHz 受信 フロントエンド内 T3 TP2 S~G 間電圧 = 最大 IF 調整 9 83MHz 90dB 変調 : OFF 83MHz 受信 TD1 R42 両端電圧 = 0V FM 同調点調整 10 83MHz 90dB 変調 : OFF 83MHz 受信 TD4 IC20 TA7310P 7pin 波形 = 最大 2nd IF 調整 オシロスコープで観測 11 83MHz 20dB 変調 : mono 1kHz 83MHz 受信 MUTE : ON VR1 MUTE ON/OFF が切り換わる境界 となるように調整 MUTE レベル調整 12 83MHz 60dB 変調 : OFF 83MHz 受信 VR2 S メータ = 4 S メータ調整 13 83MHz 90dB 変調 : stereo 1kHz 83MHz 受信 TD2 TD3 オーディオ出力 = 高調波歪率最小 IF 歪調整 14 83MHz 90dB 変調 : R/L ch. only 1kHz 83MHz 受信 VR3 L/R ch. オーディオ出力電圧 = 最小 セパレーション調整 調整結果 ステレオセパレーションなどは以下となりました。 良好な数値です。 ステレオ受信時の高調波歪率は 0.06% 程度と極少でした。 これは IF 部と検波部の性能が良い証拠です。 やはり高級チューナです。 項目 SELECTIVITY L R 単位 ステレオセパレーション NORMAL 51 57 dB パイロット信号キャリアリーク - -82 -80 dB オーディオ出力レベル偏差 (MONO) - 0 0 dB 使ってみました フロントパネル やはり Accuphase です。 デザインが秀逸です。 特に正面から見た時の豪華さに惚れ惚れします。 フロントパネルはアルミ材で、厚みが 15mm とぶ厚く、ヘアラインの眩しいシャンパンゴールドが上品で豪華です。 サイド板はアルミ材でできた飾り板で、黒の樹脂塗装がされています。 サイドウッドより好感が持てます。 [Accuphase] の文字はアイスブルー色、その他の表示はオレンジ色が主体で高級感を感じる表示です。 少し怪しい感じさえします。 巨艦に属するチューナです。 シンセサイザ方式チューナとしては大きさが最大級です。 T-109 とペアになるアンプとデザイン/サイズを合わした結果と思います。 リアパネル他 リアパネルの端子は [ANTENNA] [BALANCED OUTPUT (FIXED)] [UNBALANCED OUTPUT (FIXED)] [UNBALANCED OUTPUT (CONTROLLED)] [AC100V 入力] です。 [ANTENNA] 端子は F 端子なので、妨害電波の混入を阻止できます。 [BALANCED OUTPUT (FIXED)] は XLR 端子です。 [UNBALANCED OUTPUT (FIXED)] [UNBALANCED OUTPUT (CONTROLLED)] は通常の RCA 端子です。 これらの端子は金メッキされています。 [UNBALANCED OUTPUT (CONTROLLED)] の出力レベルはフロントパネルの [OUTPUT LEVEL] ボリュームで可変できます。 筐体には十分な剛性があります。 天板はぶ厚いです。 底板にもしっかりした黒の塗装がしてあり、手抜きはありません。 機能関連 [STATION] メモリは16局分あり十分です。 シフト操作不要でワンタッチ選局ができるので使いやすいです。 周波数だけでなく、NORMAL/NARROW などの設定情報も一緒に記憶されます。 ステーションメモリボタンの左側に6つの機能ボタンがあります。 [SELECTIVITY] ボタンで IF BAND NORMAL/NARROW 切換できます。 NORMAL というのは一般的な WIDE と同じです。 通常は NORMAL で使います。 [METER] ボタンでメータを SIGNAL/MULTIPATH に切換できます。 [MEMORY] ボタンでプリセットできます。 [FILTER] ボタンで高域雑音の FILTER OFF/ON が切り換えできます。 通常は OFF で使います。 [MUTE] ボタンで MUTE ON/OFF を切り換えます。 通常は ON で使います。 [MONO] ボタンでステレオ放送を強制的にモノラル受信することができます。 通常は OFF で使います。 中級機やローコスト機に当たり前のようにある次の機能がありません。 2世代前の T-107 には1と5の機能があります。 T-107 の S メータは電波レベルを dB 換算で表示します。 自動的に周波数を更新して受信可能な放送局をサーチする [スキャン] 機能がありません。 [プログラム] などの留守録対応機能がありません。 [Last One Play] 機能はあるので、電源 OFF 直前に選局していた放送局を電源 ON 時に受信することは可能です。 録音機の録音レベル調整に役立つ [REC CAL] 機能がありません。 変調度レベル表示機能がありません。 電波レベルを dB 換算で表示する機能がありません。 S メータは安物チューナの振れ方と大して変わりません。 評価 豪華なデザインが圧倒的です。 強大な存在感があります。 放送局のモニタ機材のような、動作の安定感があります。 無調整回路による経年変化に強い構成であることが安心感につながります。 生々しい素晴らしい音質!!! 歪感の非常に少ない嫌味の無い高解像度の音です。 音に安定感があります。 低域の音も豊富に出ます。 仕様&その他 日本語カタログ です。 英語カタログ です。 以下が仕様です。 一般のチューナではチャンピオンスペックを表示しますが、 Accuphase では 保証特性 と言っています。 チャンピオンスペックは特定の1台を厳密に調整した結果のスペックなので、量産機全部がそのスペックが出る訳ではありません。 チャンピオンスペックは参考スペックなのです。 保証特性とは、このスペック以上であることを保証しますの表示です。 信頼性に重きをおく業務機のようなスペック表示です。 一般の方にはスペックが低いかのように誤解されがちですが、そういうことはありません。 その他 発売時期 1993年12月 定価 150,000円 |
|